# Machining Custom Metal Knobs: Knurling, Finishes and Fits

Published 2026-10-28 by the Axisform engineering team. URL: https://www.machined-parts-factory.com/blog/custom-machined-metal-knobs-guide/

## Key takeaways
- Most metal knobs are turned from bar and finished in one setup to keep the bore and outside diameter concentric.
- DIN 82 defines common knurl patterns, including straight (RAA) and diamond with raised (RGE) or recessed (RGV) points.
- Anodized 6061 aluminum is the common choice; brass and stainless steel add weight and a premium feel.
- Set screw fits suit plain shafts, D-bores self-align with flatted shafts and splined bores grip knurled shafts with no visible hardware.
- Specify bore fit, runout, face perpendicularity, indicator alignment and finish allowance in the bore.

A custom machined metal knob is usually turned from aluminum, brass or stainless steel bar, knurled or textured for grip, finished by anodizing, plating or PVD, and attached with a set screw, a D-shaped bore or a splined (knurled) bore that matches the shaft. The right combination depends on the shaft you are fitting, the feel you want and the environment: anodized 6061 aluminum with a set screw suits most audio and instrument knobs, while appliance and automotive interior knobs more often need a press-fit D or spline bore and a durable finish. Getting the fit and runout right matters as much as the look, because a knob that wobbles feels cheap regardless of its finish.

## What are machined knobs used for?

Machined metal knobs appear wherever a control is touched often and should feel solid:

- **Audio:** amplifiers, preamps, mixing consoles, guitar pedals, DJ equipment and studio gear.
- **Appliances:** ovens, cooktops, coffee machines and premium kitchen equipment.
- **Automotive interiors:** volume, climate and drive-mode controls, often with tight cosmetic standards.
- **Instruments and industrial controls:** test equipment, lighting consoles and machine tools.

Compared to molded plastic knobs, machined metal knobs offer weight, rigidity, precise concentricity and finishes that plastic cannot reproduce. For higher volumes, zinc die casting with machined finishing is an alternative.

## How are metal knobs machined?

Most knobs are rotationally symmetric, so they are made on a CNC lathe or turn-mill center:

1. **Turning** the outer profile, face, skirt and bore from bar stock in one setup, which keeps the bore and outer diameter concentric.
2. **Knurling** the grip surface on the lathe.
3. **Milling** secondary features with live tooling: indicator lines, flats, cross holes for set screws, finger dimples.
4. **Broaching or wire EDM** for D-shaped or splined bores.
5. **Finishing:** bead blasting, brushing, anodizing, plating or PVD, plus laser marking.

Small knobs can be produced efficiently on Swiss-type style lathes. Knobs with off-axis features, such as a pointer skirt or an asymmetrical lever, may need 4- or 5-axis milling — see [3-axis vs 4-axis vs 5-axis CNC machining](/blog/3-axis-vs-4-axis-vs-5-axis-cnc-machining/).

## What knurling patterns are available?

Knurling creates a textured grip on the knob surface. Patterns are standardized in DIN 82:

| DIN 82 type | Pattern | Typical use |
|---|---|---|
| RAA | Straight (axial) knurl, lines parallel to the axis | Audio knobs, fine "coin edge" look, rotation grip |
| RBR / RBL | Diagonal knurl, right-hand or left-hand | Decorative, less common alone |
| RGE | Diamond knurl, raised points (male) | Strong grip, industrial and tool knobs |
| RGV | Diamond knurl, recessed points (female) | Softer feel, cleaner look |
| RKE / RKV | Cross knurl (perpendicular lines) | Decorative and grip surfaces |

### What knurl pitch should you choose?

Common pitches range from about **0.5 mm to 1.6 mm**. Fine pitches (around 0.5–0.8 mm) give a refined look and suit small audio knobs. Coarser pitches give a stronger grip for gloved hands or high-torque controls. Pitch should suit the diameter so the pattern closes evenly around the circumference.

### Form knurling vs cut knurling

- **Form (roll) knurling** presses the pattern into the surface. It is fast but slightly increases the diameter and needs a ductile material.
- **Cut knurling** removes material with sharp knurl wheels, producing crisp patterns with less force, which is better for thin-walled knobs and harder materials.

Many premium audio knobs use fine **milled or diamond-turned patterns** instead of traditional knurls: radial grooves, concentric face rings or faceted edges.

## Which materials work best for machined knobs?

| Material | Characteristics | Typical finish | Typical use |
|---|---|---|---|
| 6061 / 6063 aluminum | Light, easy to machine, excellent anodizing | Bead blast + anodize, brushed + anodize | Audio, consumer electronics |
| 7075 aluminum | Harder, sharper edges | Anodize | Premium knobs needing wear resistance |
| Brass (C36000) | Heavy, smooth feel, very machinable | Nickel, chrome or PVD plating, or polished and lacquered | Audio, luxury appliances |
| Stainless steel 303 / 304 | Durable, corrosion resistant, heavy | Brushed, bead blasted, polished, PVD | Appliances, marine, industrial |
| Titanium (Gr5) | Light, strong, distinctive color | Bead blast, anodize (interference colors), PVD | Specialty and premium products |
| Zinc alloy (die cast) | Economical at volume, heavy | Plating, painting | High-volume appliance and automotive |

**Weight matters for feel.** A heavier knob adds rotational inertia, which makes a volume knob spin more smoothly and makes detents feel more deliberate. Brass and stainless steel feel heavier than aluminum; aluminum knobs can be given brass or steel inserts for mass without the cost of a solid brass knob.

## Which finishes suit knobs?

- **Bead blast + Type II anodize:** the standard modern matte look, uniform and scratch-tolerant. See our [anodizing guide](/blog/anodizing-guide-machined-aluminum/).
- **Brushed + anodize:** linear or circular brushed grain under a clear or tinted coating.
- **Diamond-cut chamfer:** a bright, machined edge cut after anodizing for contrast.
- **Polishing:** mirror finish, best on brass and stainless steel.
- **Electroplating:** nickel and chrome on brass or zinc for a classic appearance.
- **PVD:** thin, hard decorative coatings in gold, black, gunmetal and bronze tones on stainless steel and brass, with good wear resistance.
- **Laser engraving:** indicator lines, scales and logos; on anodized aluminum the mark is crisp and permanent.

Automotive interior knobs are touched constantly and exposed to sweat, sunscreen and UV. Ask about abrasion and chemical resistance testing to your specification rather than assuming a decorative finish is enough.

## How should a knob attach to its shaft?

The attachment method is set by the shaft on the potentiometer, encoder or valve you are fitting. Measure the shaft or check its datasheet before designing the bore.

### Set screw fit

A threaded radial hole holds a grub screw (often M3 or M4) that tightens against the shaft.

- Works on plain round shafts, flatted shafts and many knurled shafts.
- Tolerant of shaft variation; easy to adjust and remove.
- Use **two set screws at 90°** for a more secure, centered grip on larger knobs.
- Use **nylon- or brass-tipped set screws** to avoid marking the shaft.
- The set screw hole is visible unless it is hidden under a cap, skirt or within a recess.

### D-shaft fit

The bore has a flat matching a D-shaped shaft, so the knob cannot rotate on the shaft and aligns automatically with the indicator line.

- Common on potentiometers, encoders and appliance controls; 6 mm D-shafts are widely used.
- Can be a **slip fit with a set screw** or a **press fit** without hardware.
- The D-bore is typically made by **broaching** or wire EDM; the flat's position relative to the indicator line must be toleranced.

### Spline or knurled-shaft fit

Many potentiometer and encoder shafts are knurled with fine axial serrations, commonly 18 or 24 teeth on 6 mm and 1/4 in shafts. A matching splined bore or a press-fit plastic or brass insert grips the shaft.

- Clean exterior with no visible screw.
- Allows indexing in small steps around the shaft.
- Requires accurate bore sizing; too tight cracks the bore or damages the shaft, too loose lets the knob slip.
- A **split shaft** with a press-on knob uses the shaft's own spring force.

### Collet fit

A collet knob uses an internal collet that is tightened through the knob face, then covered with a cap. It centers the knob precisely and fits a range of plain shafts, which is popular in professional audio equipment.

### Fit comparison

| Fit type | Exterior | Alignment | Typical use |
|---|---|---|---|
| Set screw | Visible screw (unless hidden) | Adjustable | Audio, instruments, prototypes |
| D-shaft | Clean or with set screw | Fixed, self-aligning | Appliances, encoders |
| Spline / knurled | Clean | Indexable | Potentiometers, consumer devices |
| Collet | Clean, with cap | Precise centering | Professional audio |

## What tolerances matter on a knob?

- **Bore diameter** to the shaft: a slip fit for set screw knobs, an interference fit for press-on knobs.
- **Runout** between the bore and the outer diameter — the main cause of visible wobble.
- **Face perpendicularity** to the bore.
- **Indicator line angle** relative to the D-flat or spline.
- **Finish thickness** in the bore — mask the bore or machine it to the post-finish size.

Our [tolerance guide](/blog/cnc-machining-tolerances-cost-guide/) covers how to specify these features without over-tolerancing.

## How Axisform makes knobs

Axisform produces custom knobs with CNC turning and turn-mill, broaching, wire EDM, knurling and laser marking, finished with anodizing, plating, polishing or PVD. Quantities start at one piece for prototypes. See [products](/products/) and [projects](/projects/), or send your drawing and shaft details via [contact](/contact/).

## Frequently asked questions

### What is the best material for a metal knob?

Anodized 6061 aluminum is the most common choice because it is light, easy to machine and takes uniform color. Brass and stainless steel are chosen for weight and a premium feel, and zinc die casting suits high volumes.

### What is the difference between straight and diamond knurling?

Straight knurling has lines parallel to the knob axis and gives a refined, coin-edge look with good rotational grip. Diamond knurling has crossing diagonal lines that form raised or recessed points and gives a stronger grip in every direction.

### How do I choose between a set screw and a D-shaft knob?

Use a set screw when the shaft is plain round or when you want adjustability. Use a D-shaft bore when the shaft has a flat and you want the knob to align automatically with its indicator and resist slipping without visible hardware.

### Why does my knob wobble on the shaft?

Wobble is usually caused by runout between the bore and the outer diameter, a loose bore fit or a single set screw pushing the knob off-center. Machining the bore and outside diameter in one setup and using a correct fit or two set screws fixes most cases.